Billet Aluminum Case – 3.812″ Bore

//

Billet Aluminum Case – 3.812″ Bore

Billet Aluminum Case – 3.812″ Bore

$2,600.00

Part Number: N1912PM

Out of stock

NOT SOLD INDIVIDUALLY
Pinion supports are unique to this case
Many components are case specific
Shown for technical information only

7075-T73 AEROSPACE ALUMINUM
– Superior strength & high stress resistance

VIBRATORY STRESS RELIEVED
– Utilizing sub-harmonic vibrational energy

SOLUTION HEAT TREATED
– Ensures consistent mechanical properties

.650” THICK MOUNTING FLANGE
– Provides a rigid foundation

RAISED CROSS RIB DESIGN
– Increases stiffness throughout unit

• WRAP AROUND DESIGN MAIN CAPS
– Enhances main cap strength and rigidity

AISI 8740 STEEL BULLET END MAIN STUDS
– 38% higher yield strength than typical chrome moly
– Allows increased clamping force on main caps

MASSIVE WALL SECTIONS IN TAIL BEARING AREA
– Provides exceptional tail bearing support

OIL SCAVENGING CHANNEL
– Enhanced pinion bearing lubrication

EXTENSIVE LIGHTENING ON CASE AND SUPPORT
– Removes 1.5 lbs over comparable Ultra Case

ACCEPTS 10” DEVELOPMENT GEAR SET
True finished ring gear O.D. 9.625”

TYPE II ANODIZED
– For corrosion protection

EXTRA WIDE TAIL BEARING
– Increases load capacity

BOLT-ON TAIL BEARING RETAINER
– Firmly secures tail bearing

DEDICATED 10” PINION SUPPORT AVAILABLE
– Eliminates pinion support spacer

 

See Packages Below to Build a Complete Center Section

P5381LT
3.812″ case, 9″ / 9 1/2″ tapered support, & install kit for 35 spline pinion

P5381LT-10
3.812″ case, 10″ tapered support, & install kit for 10″ 35 spline pinion

P5381LB
3.812″ case, 9″ / 9 1/2″ taper / ball support, & install kit for 35 spline pinion

P5381LB-10
3.812″ case, 10″ taper / ball support, & install kit for 10″ 35 spline pinion

 
Remaining Parts Required – Spool, Gear Set, & Yoke or Coupler

This product is only available from an Authorized Strange Dealer or Factory Direct Call - 847.663.1701 or Email Us

Parts List and Installation Guide pdf File

Description

Strange Billet Case – 3.812″ Bore

You may also like…

  • Strange Rear End

    Strange builds rear housings for all dragster classes

    Strange Rear End
  • Cobra Jet Program

    Strange builds the complete 9in rear housing for Ford's Cobra Jet Mustangs

    Cobra Jet Program
  • Mopar Drag Pack

    Strange builds the rear housings for the Mopar Drag Pack Program

    Mopar Drag Pack
  • Top Fuel Dragsters

    NHRA Top Fuel Dragsters rely on Strange to put eight thousand HP to the ground

    Top Fuel Dragsters
  • NHRA Funny Cars

    Strange manufactures many parts for Funny Cars

    NHRA Funny Cars
  • COPO Camaro

    Strange builds the complete rear housing for the GM COPO Camaro Program

    COPO Camaro
Drag Racing T-Shirt

Strange Oval

  • Strange Rear End

    Strange builds rear housings for all dragster classes

    Strange Rear End
  • Cobra Jet Program

    Strange builds the complete 9in rear housing for Ford's Cobra Jet Mustangs

    Cobra Jet Program
  • Mopar Drag Pack

    Strange builds the rear housings for the Mopar Drag Pack Program

    Mopar Drag Pack
  • Top Fuel Dragsters

    NHRA Top Fuel Dragsters rely on Strange to put eight thousand HP to the ground

    Top Fuel Dragsters
  • NHRA Funny Cars

    Strange manufactures many parts for Funny Cars

    NHRA Funny Cars
  • COPO Camaro

    Strange builds the complete rear housing for the GM COPO Camaro Program

    COPO Camaro